AFBR-703ASDZ डेटा पत्रक PDF( Datasheet डाउनलोड )

डेटा पत्रक - SFP+ Transceiver - Avago

भाग संख्या AFBR-703ASDZ
समारोह SFP+ Transceiver
मैन्युफैक्चरर्स Avago 
लोगो Avago लोगो 
पूर्व दर्शन
1 Page
<?=AFBR-703ASDZ?> डेटा पत्रक पीडीएफ

AFBR-703ASDZ pdf
Description, continued
The AFBR-703ASDZ transceiver package is compliant
with the SFF 8432 Improved Pluggable Formfactor hous-
ing specification for the SFP+. It can be installed in any
INF-8074 or SFF-8431/2 compliant Small Form Pluggable
(SFP) port regardless of host equipment operating status
The AFBR-703ASDZ is hot-pluggable, allowing the mod-
ule to be installed while the host system is operating and
on-line. Upon insertion, the transceiver housing makes
initial contact with the host board SFP cage, mitigating
potential damage due to Electro-Static Discharge (ESD).
Digital Diagnostic Interface and Serial Identification
The two-wire interface protocol and signaling detail
are based on SFF-8431. Conventional EEPROM mem-
ory, bytes 0-255 at memory address 0xA0, is organized
in compliance with SFF-8431. New digital diagnostic
information, bytes 0-255 at memory address 0xA2, is
compliant to SFF-8472. The new diagnostic information
provides the opportunity for Predictive Failure Identifi-
cation, Compliance Prediction, Fault Isolation and Com-
ponent Monitoring.
Predictive Failure Identification
The AFBR-703ASDZ predictive failure feature allows a
host to identify potential link problems before system
performance is impacted. Prior identification of link
problems enables a host to service an application via
“fail over”to a redundant link or replace a suspect device,
maintaining system uptime in the process. For applica-
tions where ultra-high system uptime is required, a digi-
tal SFP provides a means to monitor two real-time laser
metrics asso­ciated with observing laser degradation and
predicting failure: average laser bias current (Tx_Bias)
and average laser optical power (Tx_Power).
Compliance Prediction
Compliance prediction is the ability to determine if an
optical transceiver is operating within its operating and
environmental requirements. AFBR-703ASDZ devices
provide real-time access to transceiver internal supply
voltage and temperature, allowing a host to identify po-
tential component compliance issues. Received optical
power is also available to assess compliance of a cable
plant and remote transmitter. When operating out of re-
quirements, the link cannot guarantee error free trans-
Fault Isolation
The fault isolation feature allows a host to quickly pin-
point the location of a link failure, minimizing downtime.
For optical links, the ability to identify a fault at a local
device, remote device or cable plant is crucial to speed-
ing service of an installation. AFBR-703ASDZ real-time
monitors of Tx_Bias, Tx_Power, Vcc, Temperature and
Rx_Power can be used to assess local transceiver current
operating conditions. In addition, status flags TX_DIS-
ABLE and Rx Loss of Signal (LOS) are mirrored in memory
and available via the two-wire serial interface.
Component Monitoring
Component evaluation is a more casual use of the AFBR-
703ASDZ real-time monitors of Tx_Bias, Tx_Power, Vcc,
Temperature and Rx_Power. Potential uses are as debug-
ging aids for system installation and design, and trans-
ceiver parametric evaluation for factory or field qualifi-
cation. For example, temperature per module can be
observed in high density applications to facilitate ther-
mal evaluation of blades, PCI cards and systems.

विन्यास 19 पेज
डाउनलोड[ AFBR-703ASDZ Datasheet.PDF ]

शेयर लिंक

अनुशंसा डेटापत्रक

भाग संख्याविवरणविनिर्माण
AFBR-703ASDZSFP+ TransceiverAvago

भाग संख्याविवरणविनिर्माण
30L120CTSchottky RectifierPFC Device
PFC Device
AT28C010-12DKSpace 1-MBit (128K x 8) Paged Parallel EEPROMATMEL
FAE391-A20AM/FM Automotive Electronic TunerMitsumi

Index : 0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z    |   2017   |  संपर्क   |   खोज     |   English