DataSheet.in

K3000F1 डेटा पत्रक PDF( Datasheet डाउनलोड )


डेटा पत्रक - silicon bilateral voltage triggered switch - Teccor

भाग संख्या K3000F1
समारोह silicon bilateral voltage triggered switch
मैन्युफैक्चरर्स Teccor 
लोगो Teccor लोगो 
पूर्व दर्शन
1 Page
		
<?=K3000F1?> डेटा पत्रक पीडीएफ

K3000F1 pdf
Electrical Specifications
Type
Part No.
IT(RMS) VDRM
On-State
RMS Current
TJ125°C
50/60Hz
Sine Wave
(7) (8)
Repetitive
Peak
Off-State
Voltage
TO-92
E Package
DO-15X
G Package
TO-202AB
F Package
DO-214AA
S Package
See “Package Dimensions” section for variations.
K1050E70
K1050G
K1050S
K1100E70
K1100G
K1100S
K1200E70
K1200G
K1200S
K1300E70
K1300G
K1300S
K1400E70
K1400G
K1400S
K1500E70
K1500G
K1500S
K2000E70
K2000G
K2000F1
K2000S
K2200E70
K2200G
K2200F1
K2200S
K2400E70
K2400G
K2400F1
K2400S
K2401F1
K2500E70
K2500G
K2500F1
K2500S
K3000F1
Amps
MAX
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0 (10)
1.0
1.0
Volts
MIN
±90
±90
±90
±90
±90
±90
±180
±180
±190
±190
±190
±190
VBO
Breakover Voltage
50/60Hz Sine Wave
(1)
IDRM
IBO
Repetitive Breakover
Peak
Current
Off-State 50/60Hz
Current Sine Wave
50/60Hz
Sine Wave
V=VDRM
Volts
MIN MAX
95 113
104 118
110 125
120 138
130 146
140 170
190 215
205 230
220 250
220 250
240 280
270 330
µAmps
MAX
5
5
5
5
5
5
5
5
5
5
5
5
µAmps
MAX
10
10
10
10
10
10
10
10
10
10
10
10
General Notes
• All measurements are made at 60Hz with a resistive load at an
ambient temperature of +25°C unless otherwise specified.
• Storage temperature range (TS) is -65°C to +150°C.
• The case (TC) or lead (TL) temperature is measured as shown on
the dimensional outline drawings. See “Package Dimensions” sec-
tion of this catalog.
• Junction temperature range (TJ) is -40°C to +125°C.
• Lead solder temperature is a maximum of +230°C for 10 seconds
maximum; 1/16" (1.59mm) from case.
Electrical Specification Notes
(1) See Figure 9.6 for VBO change vs junction temperature.
(2) See Figure 9.7 for IBO vs junction temperature.
(3) See Figure 9.2 for IH vs case temperature.
(4) See Figure 9.14 for test circuit.
(5) See Figure 9.1 for more than one full cycle rating.
(6) RθJA for TO-202 Type 23 and Type 41 is 70°C/watt.
(7) TC 90°C for TO-92 Sidac and TC 105°C for TO-202 Sidacs.
TL 100°C for DO-15X and TL 90°C for DO-214AA.
(8) See Figure 9.15 for clarification of Sidac operation.
(9) For best Sidac operation, the load impedance should be near or
less than switching resistance.
(10) Teccor's new, improved series of sidacs is designed to ensure
goodcommutationathigherswitchingfrequenciesasrequiredinignitor
circuits for high intensity discharge (HID) lighting. A typical circuit
for a metal halide lamp ignitor is shown in the schematic, Figure
9.3. With proper component selection this circuit will produce three
pulses for ignition of Osram lamp types such as HQI-T70W, HQI-
T150W, and HQI-T250W which require a minimum of three pulses
at 4kV magnitude and >1µs duration each at a minimum repetition
rate of 3.3kHz.
SIDAC
9-2 Teccor Electronics
(972) 580-7777

विन्यास 6 पेज
डाउनलोड[ K3000F1 Datasheet.PDF ]


शेयर लिंक


अनुशंसा डेटापत्रक

भाग संख्याविवरणविनिर्माण
K3000F1silicon bilateral voltage triggered switchTeccor
Teccor


भाग संख्याविवरणविनिर्माण
30L120CTSchottky RectifierPFC Device
PFC Device
AT28C010-12DKSpace 1-MBit (128K x 8) Paged Parallel EEPROMATMEL
ATMEL
B20NM50FDN-CHANNEL POWER MOSFETSTMicroelectronics
STMicroelectronics
D8442SD844SavantIC
SavantIC
FAE391-A20AM/FM Automotive Electronic TunerMitsumi
Mitsumi


Index : 0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z



www.DataSheet.in    |   2017   |  संपर्क   |   खोज     |   English