DataSheet.in

GW64x32C-K610A डेटा पत्रक PDF( Datasheet डाउनलोड )


डेटा पत्रक - VFD Module - NORITAKE ITRON

भाग संख्या GW64x32C-K610A
समारोह VFD Module
मैन्युफैक्चरर्स NORITAKE ITRON 
लोगो NORITAKE ITRON लोगो 
पूर्व दर्शन
1 Page
		
<?=GW64x32C-K610A?> डेटा पत्रक पीडीएफ

GW64x32C-K610A pdf
Active Matrix Graphic VFD Module
GW64x32C-K610A
SOFTWARE COMMANDS
Instruction
UDF Write
(BUSY = 14ms)
Hex
00H-0FH
Cursor Positioning
(BUSY = 50us)
10H+x+y
Pixel On
(BUSY = 14ms)
Pixel Off
(BUSY = 14ms)
Area Fill
(BUSY = 50us & 14ms [last byte])
Area Clear
(BUSY = 50us & 14ms [last byte])
Area Invert
(BUSY = 50us & 14ms [last byte])
Box Outline
(BUSY = 50us & 14ms [last byte])
Draw Line
(BUSY = 50us & 14ms [last byte])
11H
12H
13H+x1+y1+x2+y2
14H+x1+y1+x2+y2
15H+x1+y1+x2+y2
16H+x1+y1+x2+y2
17H+x1+y1+x2+y2
Vertical Graphic Write
(BUSY = 50us & 14ms [last byte])
Horizontal Graphic Write
(BUSY = 50us & 14ms [last byte])
UDF Store
(BUSY = 50us and 4ms for each UDF data byte)
18H+dir+num+data
19H+dir+num+data
1AH+UDF+data
Escape
(BUSY = 50us)
Mini Font
(BUSY = 50us)
5x7 Font
(BUSY = 50us)
10x14 Font
(BUSY = 50us)
20x28 Font
(BUSY = 50us)
ASCII Write
(BUSY = 14ms)
ESCAPE COMMANDS
Automatic Latch
(BUSY = 50us)
PSU Off
(BUSY = 50us)
Luminance
(BUSY = 50us)
Manual Latch
(BUSY = 50us)
PSU On
)(BUSY = 50us
RESET
(BUSY = 15ms)
1BH+x…
1CH
1DH
1EH
1FH
20H-7FH
1BH+41H
1BH+46H
1BH+4CH+n
1BH+4DH
1BH+4FH
1BH+52H
Description
Display user defined character (0-15) at current cursor position. The cursor is shifted 8 pixels
on each UDF write. All UDF characters have an 8x8-pixel format and can be defined using
the ‘UDF Store’ command.
Set cursor position. X = 0 to 63, Y = 0 to 31. The cursor can be positioned off-screen in the
vertical direction. The cursor position is automatically advanced on each character write. A
cursor position of 0,0 defines the top left-hand corner of the display.
Turn off single pixel at current cursor position.
Turn on single pixel at current cursor position.
Turn on all pixels within co-ordinates x1, y1 to x2, y2. The first co-ordinates x1, y1 should
point to the top-left of the area, and x2, y2 should point to the bottom-right.
Turn off all pixels within co-ordinates x1, y1 to x2, y2. The first co-ordinates x1, y1 should
point to the top-left of the area, and x2, y2 should point to the bottom-right.
Invert all pixels within co-ordinates x1, y1 to x2, y2. The first co-ordinates x1, y1 should point
to the top-left of the area, and x2, y2 should point to the bottom-right.
Draw single pixel width box outline from x1, y1 to x2, y2. The first co-ordinates x1, y1 should
point to the top-left of the area, and x2, y2 should point to the bottom-right.
Draw a single pixel width line from x1, y1 to x2, y2. Both co-ordinates must be within the
display area.
e.g. 17H+00H+00H+3FH+1FH - draws a diagonal line from the top-left corner to the
bottom-right corner.
Display vertical graphic data (D7 uppermost). Data direction can be either horizontal (0) or
vertical (1). Data is displayed on last data byte sent. See ‘Graphical Data Writes’ below.
Display horizontal graphic data (D7 leftmost). Data direction can be either horizontal (0) or
vertical (1). Data is displayed on last data byte sent. See ‘Graphical Data Writes’ below.
Store user defined character (00H-0FH) in non-volatile EEPROM. Characters are in an 8x8-
pixel format The character data should consist of 8 vertical bytes with the MSB uppermost.
e.g. 1AH+05H+FFH+81H+81H+81H+81H+81H+81H+FFH - defines a box at user defined
character 05H.
05H - display box character
Perform extended command, see ‘Escape Command’ table below.
Select proportional mini font. The cursor movement amount is dictated by the width of the
character written, plus a one-pixel gap.
Select 5x7 font (default). The cursor is advanced by 6 pixels on each character write.
Select 10x14 font. The cursor is advanced by 12 pixels on each character write.
Select 20x28 font. The cursor is advanced by 24 pixels on each character write.
Text is written to the display in the selected font. The cursor is moved right on each character
write, if the end of the display is reached, the cursor will move back to the left-hand side of
the display.
All data written is immediately displayed. (default)
Turn off the VFD Module’s PSU. All data communication remains active.
Set display luminance level n = 0 (display off), 1 (minimum) to 7 (maximum). (default = 7)
All hidden data is displayed. All subsequent written data is hidden until the next manual
latch command. This can be helpful for slow display updates.
Enable VFD module’s PSU. (default)
Reset module to power on defaults. Luminance level is set to maximum. Display is cleared.
5x7 font is selected. Automatic latch is enabled. Cursor is positioned to 0,7. ‘R’ is sent to
the host.
GRAPHICAL DATA WRITES
CURSOR
POSITION
MSB
DATA
DIRECTION
CURSOR
POSITION
MSB
DATA
DIRECTION
CURSOR
POSITION
DATA
DIRECTION
MSB
CURSOR
POSITION
DATA
DIRECTION
MSB
Vertical Data & Horizontal
Movement
Vertical Data & Vertical
Movement
Horizontal Data & Horizontal
Movement
Horizontal Data & Vertical
Movement
NORITAKE ITRON VFD MODULES
GW64x32C-K610A

विन्यास 4 पेज
डाउनलोड[ GW64x32C-K610A Datasheet.PDF ]


शेयर लिंक


अनुशंसा डेटापत्रक

भाग संख्याविवरणविनिर्माण
GW64x32C-K610AVFD ModuleNORITAKE ITRON
NORITAKE ITRON


भाग संख्याविवरणविनिर्माण
30L120CTSchottky RectifierPFC Device
PFC Device
AT28C010-12DKSpace 1-MBit (128K x 8) Paged Parallel EEPROMATMEL
ATMEL
B20NM50FDN-CHANNEL POWER MOSFETSTMicroelectronics
STMicroelectronics
D8442SD844SavantIC
SavantIC
FAE391-A20AM/FM Automotive Electronic TunerMitsumi
Mitsumi


Index : 0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z



www.DataSheet.in    |   2017   |  संपर्क   |   खोज     |   English