DataSheet.in

ZSSC3015 डेटा पत्रक PDF( Datasheet डाउनलोड )


डेटा पत्रक - Sensor Signal Conditioner - Zentrum Mikroelektronik Dresden

भाग संख्या ZSSC3015
समारोह Sensor Signal Conditioner
मैन्युफैक्चरर्स Zentrum Mikroelektronik Dresden 
लोगो Zentrum Mikroelektronik Dresden लोगो 
पूर्व दर्शन
1 Page
		
<?=ZSSC3015?> डेटा पत्रक पीडीएफ

ZSSC3015 pdf
ZSSC3015
RBicdLite-Auto™ Sensor Signal Conditioner with Diagnostics
Brief Description
The ZSSC3015 RBicdLite-Autosensor signal condi-
tioner IC is adjustable to nearly all piezo-resistive
bridge sensors. Measured and corrected bridge
values are provided at the Sig™ pin, which can be
configured as an analog voltage output or as a one-
wire serial digital output.
The ZACwire™ digital one-wire interface (OWI) can
be used for a simple PC-controlled calibration
procedure to program a set of calibration coefficients
into an on-chip EEPROM. The calibrated ZSSC3015
and a specific sensor are mated digitally: fast,
precise, and without the cost overhead associated
with trimming by external devices or laser. Integrated
diagnostics functions make the ZSSC3015
particularly well-suited for automotive applications.
Features
Digital compensation of sensor offset, sensitivity,
temperature drift, and nonlinearity
Programmable analog gain and digital gain;
accommodates bridges with spans < 1mV/V
and high offset
Many diagnostic features on chip (e.g., EEPROM
signature, bridge connection checks, bridge short
detection, power loss detection)
Independently programmable high and low
clipping levels
24-bit customer ID field for module traceability
Internal temperature compensation reference (no
external components)
Option for external temperature compensation
with addition of single diode
Output options: rail-to-rail ratiometric analog
voltage (12-bit resolution), absolute analog
voltage, ZACwire™ digital one-wire interface
Fast power-up to data out response; output
available 5ms after power-up
Current consumption depends on programmed
sample rate and mode: 1mA down to 300µA (typ.)
Fast response time: 1.4ms typical
High voltage protection: 30V with external JFET
AEC-Q100 qualified
Benefits
No external trimming components required
PC-controlled configuration and calibration via
ZACwire™ one-wire interface simple, low cost
High accuracy (as high as ±0.1% FSO @ -25 to
85°C; ±0.25% FSO @ -50 to 150°C)
Single-pass calibration quick and precise
Available Support
Evaluation Kit available
Mass Calibration System available
Support for industrial mass calibration available
Quick circuit customization possible for large
production volumes
Physical Characteristics
Wide operation temperature: 50°C to +150°C
Supply voltage 2.7 to 5.5V; with external JFET,
5.5 to 30V
Small SOP8 package
ZSSC3015 Application Circuit
VDD
Sig
ZSSC3015
VBP
VBN
Vgate
VSS
Vsupply
+2.7 to +5.5 V
OUT/OWI
0.1 F
Ground
For more information, contact ZMDI via SSC@zmdi.com.
© 2013 Zentrum Mikroelektronik Dresden AG Rev. 1.02 March 25, 2013 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated,
stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice.

विन्यास 30 पेज
डाउनलोड[ ZSSC3015 Datasheet.PDF ]


शेयर लिंक


अनुशंसा डेटापत्रक

भाग संख्याविवरणविनिर्माण
ZSSC3015Sensor Signal ConditionerZentrum Mikroelektronik Dresden
Zentrum Mikroelektronik Dresden
ZSSC3015Sensor Signal ConditionerIDT
IDT


भाग संख्याविवरणविनिर्माण
30L120CTSchottky RectifierPFC Device
PFC Device
AT28C010-12DKSpace 1-MBit (128K x 8) Paged Parallel EEPROMATMEL
ATMEL
B20NM50FDN-CHANNEL POWER MOSFETSTMicroelectronics
STMicroelectronics
D8442SD844SavantIC
SavantIC
FAE391-A20AM/FM Automotive Electronic TunerMitsumi
Mitsumi


Index : 0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z



www.DataSheet.in    |   2017   |  संपर्क   |   खोज     |   English